Walnut Board Natural Oiled Clear 19x135mm

Walnut Board Natural Oiled Clear 19x135mm

Walnut Board Natural Oiled Clear 19x135mm: Walnut is a beautiful dark and intense brown hardwood with a high-end look. This species is rich in detail and its warm tones are sure to bring a room to life. The rich dark brown hues of Walnut combine with subtle tonal variations, resulting in a luxurious and unique floor.

Our engineered wood flooring meets modern requirements and keeps a traditional wood flooring appearance. The multiple layers of plywood backing give support to the visible top layer of the precious hardwood, resulting in a floor that looks and feels like a solid wood floor but that is suitable for under floor heating, can be laid over almost all types of sub floor, and can still be sanded and re-finished after years of use.

Our lacquered floors give a subtle boost to the wood surface but still retain a natural look and feel.

Technical details

Our engineered board has been produced using a Baltic WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.

The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg. Thermal conductivity (W/mK) is 0,10W/mK.

Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, Factory lacquered ready to use

Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.

Product code: WNF/160

Species: Walnut

Group: Flooring

Category: Engineered Flooring

Sub-Category: Engineered Pre-Oiled

Type of finish: Oiled – An additional coat is recommended.

Brushed: No

Profile: Tongue and Groove

Specification: Bevelled Edge

Weight: 13 kg

Recommended Use: Light Domestic

Dimensions: 135 × 19 mm

Width: 135 mm

Thickness: 19 mm

Colour : Dark

Under Floor Heating : Yes

Unit Measurement : per Square Metre

Design : Wide Boards (150mm – 300mm), Engineered

Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.

Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.

Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.

Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.

Pre-Oiled: This product is supplied with a Factory UV Oiled surface. We recommend that an additional coat of oil is applied to the surface prior to regular use.

Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.

Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.