Wenge Board Natural Unsealed 15x135mm: the Rich dark tone and wonderful grain structure of Wenge offer a luxurious appearance. The ply backing of an engineered floor with a hardwood veneer glued on top gives our engineered floors the same beautiful appearance of a solid wood floor but with superior construction, greater stability, and compatibility with under floor heating.
Wenge Board Natural Unsealed 15x135mm: the Rich dark tone and wonderful grain structure of Wenge offer a luxurious appearance. The ply backing of an engineered floor with a hardwood veneer glued on top gives our engineered floors the same beautiful appearance of a solid wood floor but with superior construction, greater stability, and compatibility with under floor heating.
This engineered overlay wood flooring meets modern requirements and keeps a traditional wood flooring appearance. The multiple layers of plywood backing give support to the visible top layer of the precious hardwood, resulting in a floor that looks and feels like a solid wood floor but with a much more efficient use of precious material and that can still be sanded and re-finished after years of use. An overlay floor must be laid over an existing subfloor.
The engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The unsealed board is supplied with a micro bevel along the length of the board, pre- sanded requiring only a light 100/120 grit sand to finish.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Type of Finish: Unseald
Brushed: No
Profile: Tongue and Groove
Specification: Bevelled Edge
Unit Weight: 12kg
Size: 135 x 15 mm
Width: 135 mm
Thickness: 15 mm
Suitable for underfloor heating: Yes
Nail Fitting: Nail fixing is usually done via a nail gun, e.g Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Each wood flooring project is different so an individual approach is a must for us. We've created this cost calculator with this in mind and we hope it will be helpful to you in bringing some much-needed clarity.
Please fill in as many fields as possible with the most accurate and available information. This will increase the quality of the end result.
Please sign in first.
Sign in
