Oak Board Natural Oiled White 20x180mm

Oak Board Natural Oiled White 20x180mm

This fresh and bright feeling floor has the mid-brown tones of Oak mixed with the dazzling, but not overpowering, white oil. This finish will brighten up a space and create a clean, fresh look.

Oak is a versatile species that takes pigments very well, so it lends itself well to pre-sealed flooring. The physical characteristics that give Oak its charm are still visible through the finish, so this floor has a naturally charming character and can be matched with the desired design scheme.

Oil finishes penetrate into the wood to protect the timber and in doing so, enhance the grain. This adds depth to the wood’s natural appearance in the process.

With an engineered floor, you get the same look and feel of a traditional solid wood floor but with the added benefits of more efficient use of precious materials, superior construction, and compatibility with under floor heating.

Technical details

Our engineered board has been produced using WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.

The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg. Thermal conductivity (W/mK) is 0,10W/mK.

Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use *if the product is being laid in a high traffic environment then an additional coat of oil is recommended.

Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.

Product code: OLWO/180

Species: Oak

Group: Flooring

Category: Engineered Flooring

Sub-Category: Engineered Pre-Oiled

Type of finish: Oiled – An additional coat is recommended.

Brushed: Light

Profile: Tongue and Groove

Specification: Bevelled Edge

Weight: 14.3 kg

Recommended Use: Domestic and Light Commercial

Dimensions: 180 × 20 mm

Width: 180 mm

Thickness: 20 mm

Colour : Light

Under Floor Heating : Yes

Unit Measurement : per Square Metre

Design : Wide Boards (150mm – 300mm), Engineered

Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.

Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.

Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.

Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.

Pre-Oiled: This product is supplied with a Factory UV Oiled surface. The Natural Wood Floor Company recommends that an additional coat of oil is applied to the surface prior to regular use.

Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.

Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.