Premier Oak has a more uniform and cleaner look that brings a refined elegance to a home. The lower knot content of premier Oak gives a more contemporary appearance. Oak is a versatile species that takes pigments very well, so it lends itself well to pre-sealed flooring. The physical characteristics that give Oak its charm are still visible through the finish, so this floor has a naturally charming character and can be matched with the desired design scheme.
The distinctive knots of our natural Oak give this floor a charming character that will bring a truly unique look to a home.
Clear Oiled Oak accentuates the natural characteristics of the species, letting the golden honeyed tones come through. The warm and rich tone of the wood is emphasised by the finish, which has no added colouring.
The warm and rich tone of the wood is emphasised by the finish, which has no added colouring. Oil finishes penetrate into the wood to protect the timber and in doing so, enhance the grain. This adds depth to the wood's natural appearance in the process.
Boards with a width of 240 mm or above have a very contemporary feel and create a modern, streamline look. However, contrary to what many believe, wide boards aren’t just for large, open-plan rooms. With fewer joins than narrower boards, wide boards create a seamless clean look, so there’s less to distract the eye. This can really help to open up a space and shows off all the beauty of the timber in the process.
With an engineered floor, you get the same look and feel of a traditional solid wood floor but with the added benefits of more efficient use of precious materials, superior construction, and compatibility with under floor heating.
The engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The unsealed board is supplied with a micro bevel along the length of the board, pre- sanded requiring only a light 100/120 grit sand to finish.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Type of Finish: Oiled - An additional coat is recommended.
Profile: Tongue and Groove
Specification: Bevelled Edge
Unit Weight: 15kg
Size: 240 x 20 mm
Width: 240 mm
Thickness: 20 mm
Suitable for underfloor heating: Yes
Nail Fitting: Nail fixing is usually done via a nail gun, e.g Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Pre-Oiled: This product is supplied with a Factory UV Oiled surface. Fin Wood recommends that an additional coat of oil is applied to the surface prior to regular use.