Oak Board Natural Oiled Old White 15x180mm

Oak Board Natural Oiled Old White 15x180mm

For those who prefer the muted tones of natural wood, Old White is a stunning floor which boasts a delicate spectrum of creamy buttermilk shades mixed with the sandy tones of oak. Like all our flooring, Old White is manufactured using cutting edge techniques and is designed to last a lifetime.

Oak is a highly popular species that is a real classic and is suitable for a wide range of finishes and appearances, so that you can achieve the style you want.

Our Engineered overlays have the same beautiful look and feel of solid wood but with a much more efficient use of material. Engineered overlay flooring can only be laid over an existing subfloor, not as a structural floor. Overlays are made up of a top layer of precious hardwood with a multi-layer ply backing, meaning this floor has the same beautiful appearance of solid wood but is a much more efficient and sustainable use of material.

Technical details

Our engineered board has been produced using WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.

The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg. Thermal conductivity (W/mK) is 0,10W/mK.

Suitable for secret fixing to a ply subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The board is supplied with a micro bevel along the length of the board, factory Oiled ready to use. *if the product is being laid in a high traffic environment then an additional coat of oil is recommended.

Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor.

Product code: OLOLDW/180

Species: Oak

Group: Flooring

Category: Engineered Flooring

Sub-Category: Engineered Overlay

Type of finish: Oiled – An additional coat is recommended.

Brushed: No

Profile: Tongue and Groove

Specification: Bevelled Edge

Weight: 11 kg

Recommended Use: Domestic and Light Commercial

Dimensions: 180 × 15 mm

Width: 180 mm

Thickness: 15 mm

Colour : Light

Under Floor Heating : Yes

Unit Measurement : per Square Metre

Design : Wide Boards (150mm – 300mm), Engineered

Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.

Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.

Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.

Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.

Pre-Oiled: This product is supplied with a Factory UV Oiled surface. The Natural Wood Floor Company recommends that an additional coat of oil is applied to the surface prior to regular use.

Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.

Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.