Oak Board Natural Lacquered White-washed 15x160mm: A fantastic floor for those who prefer a less intense white than the Pure White boards.These 160 mm boards combine the best characteristics that oak has to offer, with a simple white wash effect.
Oak Board Natural Lacquered White-washed 15x160mm: A fantastic floor for those who prefer a less intense white than the Pure White boards.These 160 mm boards combine the best characteristics that oak has to offer, with a simple white wash effect.
The result is a striking visual effect, which can either act as a backdrop for more vivid colours or become a focal point in more refined and simple decorating schemes.
Our overlay boards are designed to be laid over a subfloor, whether concrete or an existing wood floor. Once laid, this floor looks and feels the same as all of our beautiful wood flooring but cannot be used as a structural floor.
The engineered board has been produced using a Russian WBP birch ply, manufactured to European standard EN 326-2. The adhesive used to bond the board is an E1 category, PUR adhesive (formaldehyde free) to DIN/EN 14257 and DIN/EN 204 low emission glue which is heat and water resistant in accordance with BS EN 14342:2005+A1. The top layer is kiln dried to between 8-12% moisture content.
The formaldehyde emissions are: 0,01 ppm, pentachlorophenol emissions: <0.8 mg/kg.
Thermal conductivity (W/mK) is 0,10W/mK.
Suitable for secret fixing to ply, battens or joist subfloor, floating on an underlay or a fully bonded installation to a screed subfloor. The unsealed board is supplied with a micro bevel along the length of the board, pre- sanded requiring only a light 100/120 grit sand to finish.
Compatible for use in conjunction with underfloor heating the board complies with BS 8201:2011, rated in accordance with BS EN 13501-1, and is classified D fl -S1 when laid as a fixed floor on a structural subfloor or E fl- S1 when laid on battens or joists for minimal smoke production.
Product code: OLOWF/160
Species: Oak
Group: Flooring
Category: Engineered Flooring
Sub-Category: Engineered Overlay
Type of finish: Engineered Overlay
Brushed: Millrun
Profile: Lacquered
Specification: Light
Weight: 10 kg
Recommended Use: per Square Metre
Pack Size: Yes
Dimensions: 160 × 15 mm
Width: 160 mm
Thickness: 15 mm
Colour : Light
Under Floor Heating : Tongue and Groove
Unit Measurement : Bevelled Edge
Design : Wide Boards (150mm – 300mm), Engineered
Engineered: 2 part Engineered floor with a Hardwood top surface bonded to a multilayer waterproof Russian Birch Plywood. Can be Nailed, Stuck Down, or Floated depending on the sub floor. All floors are Tongue and Groove with Ends Matched unless stated otherwise.
Floating: A floating floor is not physically connected to the sub floor. Normally laid on an underlay, the floor is joined by gluing the tongue and groove together or by using a click system.
Micro Bevelled: Micro Bevelled means a very small v shape can be seen on the long sides of the boards. The ends have no bevel.
Nail Fitting: Nail fixing is usually done via a nail gun, e.g. Porta-Nailer, where a serrated nail is inserted through the tongue at 45 degrees.
Pre-Lacquered: This product is supplied with a Factory UV Lacquered surface. This product is suitable to walk on immediately.
Stick Down: Sticking involves the use of an adhesive to bond the wood flooring to either a concrete/screed sub floor or to a ply/chipboard sub floor.
Under Floor Heating: This product is compatible for use over an electric or water under floor heating system. The maximum temperature must not exceed 27 degrees Celsius at the floor surface.
Each wood flooring project is different so an individual approach is a must for us. We've created this cost calculator with this in mind and we hope it will be helpful to you in bringing some much-needed clarity.
Please fill in as many fields as possible with the most accurate and available information. This will increase the quality of the end result.
Please sign in first.
Sign in
